Delock Przełącznik WLAN Power Socket MQTT z monitorowaniem energii

Numer artykułu 11827
11827 Delock Przełącznik WLAN Power Socket MQTT z monitorowaniem energii
11827
11827
11827
11827
11827 Delock Przełącznik WLAN Power Socket MQTT z monitorowaniem energii small 1
11827 small 2
11827 small 3
11827 small 4
11827 small 5

Opis

Przełącznik gniazda zasilania Delock może być sterowany przyciskiem lub przez WLAN. Przełącznik z firmware Tasmota można zintegrować z istniejącymi systemami automatyki domowej IoT lub M2M. Za pomocą interfejsu internetowego gniazdo może być sterowane bez użycia chmury bądź appki.

Monitorowanie pobór energii
Wystarczy spojrzenie aby wiedzieć jaki jest pobór energii. Pozwala efektywnie wykorzystywać energię, szacować koszty i wykrywać odstępstwa od normalnych warunków pracy.


Specyfikacja

  • Złącze:
    1 x wtyk CEE 7/4
    1 x gniazdo CEE 7/3
  • Przełącznik z dwukolorowym wskaźnikiem LED źródła
  • Interfejs internetowy
  • Programowalne sterowanie zegarem
  • Monitorowanie energii:
    Napięcie, prąd i moc
    Pobór w kilowatogodzinach
  • Obsługa MQ Telemetry Transport (MQTT), Domoticz, Home Assistant
  • Obsługa Alexa
  • Chipset: ESP8285
  • Zgodność z IEEE 802.11b/g/n
  • Zakres częstotliwości: 2,4 GHz
  • Moc transmisji (EIRP): 100 mW
  • Do użytku wewnątrz budynków
  • Pobór mocy: maks. 1,5 W
  • Napięcie wejściowe: 230 V
  • Prąd: max. 16 A
  • Moc wyjściowa: maks. 2500 W
  • Wymiary bez wtyczki: średnica ok. 51 mm, wysokość ok. 45 mm


Wymagania systemowe

  • Bramka WLAN


Zawartość opakowania

  • Przełącznik Gniazda Zasilania WLAN
  • Instrukcja obsługi


Opakowanie

  • Retail Box

Technical characteristics
Frequency range
• 2.4 GHz band
Physical characteristics
Diameter
• 51 mm
Height
• 45 mm
Kolor
• biały
What is the user name for the web interface if a password has been assigned? The default user name is "admin".
The energy monitoring is not accurate. Due to component tolerances and manufacturing, the device allows only an approximate measurement of the power. If necessary, e.g. after a reset, it is possible to obtain a better result by calibration: https://tasmota.github.io/docs/Power-Monitoring-Calibration/
Alternatively you can use a rough estimate with following console commands: CurrentCal 3300, PowerCal 10000, VoltageCal 1650.
How to flash the device to the latest Tasmota version? For the socket switch we use a version of Tasmota, that we have adjusted and tested. Please understand that we can only support this Tasmota version.
What are the changes in firmware 6.7.1? • Fix WeMo emulation for 1G echo and 2G echo dot.
• Add command "time" to disable NTP and set UTC time.
• Removed support for WPS.
What are the changes in firmware 7.2? • Change default GUI to dark theme
• New Arduino Core version
• The LED is now controlled in the same way as Tasmota
• For the hardware configuration a user template is now used.
We recommend you save the device settings and do a "Reset 6" as console command. This will restore the default settings, but keep the WIFI SSID and Password.
Weaker Wi-Fi signal after firmware upgrade The Wi-Fi calibration needs to be deleted to force the device to re-calibrate Wi-Fi after it restarts.
1. Run "reset 3" in the Console (your existing settings will not be affected).
2. The device will restart
3. Cycle the power on the device (unplug and plug it).
Wi-Fi calibration will not be done unless the device performs a cold boot from power up.
Configuration options In case of problems, the following switches can help:
SetOption55 mDNS service 0 = disable 1 = enable
SetOption19 Set Home Assistant discovery protocol 0 = use Tasmota integration (default) 1 = use MQTT discovery
SetOption109 0 = (default) 1 = force gen1 Alexa mode, for Echo Dot 2nd gen devices only
How to reset the energy values? You can enter these console commands to reset the values for today1 / yesterday2 / total3:
"EnergyReset1 0" / "EnergyReset2 0" / "EnergyReset3 0".
The device does not connect to the Wi-Fi If your device does not connect to your Wi-Fi and you've made sure the Wi-Fi credentials are correct, it is caused by using special chars or white spaces in your SSID or Password of your Wi-Fi. Remove them and try again. Other reason can be using an SSID longer than the allowed 32 characters.
Wszelkie pojawiające się tutaj nazwy i znaki należą do ich odpowiednich właścicieli. Błędy drukarskie, zmiany & pomyłki zastrzeżone.