Delock WLAN switch napájecí zásuvky MQTT

Číslo produktu 11826
11826 Delock WLAN switch napájecí zásuvky MQTT
11826
11826
11826
11826
11826
11826
11826
11826 Delock WLAN switch napájecí zásuvky MQTT small 1
11826 small 2
11826 small 3
11826 small 4
11826 small 5
11826 small 6
11826 small 7
11826 small 8

Popis

Tento switch s napájecími zásuvkami od firmy Delock je ovladatelný tlačítkem nebo přes síť WLAN. Je-li nainstalovaný firmware Tasmota, lze switch snadno integrovat do stávajících systémů automatizace domácnosti, IoT nebo M2M. Pomocí webového rozhraní lze napájecí zásuvku ovládat, aniž by bylo třeba spoléhat na prostředí cloud nebo na aplikaci.


Specifikace

  • Konektor:
    1 x zástrčka CEE 7/4
    1 x zásuvka CEE 7/3
  • Tlačítko přepínače s 2-barevným LED indikátorem
  • Webové rozhraní
  • Programovatelné ovládání času
  • Podporuje MQ Telemetry Transport (MQTT), Domoticz, Home Assistant
  • Podporuje Alexa
  • Chipset: ESP8285
  • Kompatibilní s IEEE 802.11b/g/n
  • Frekvenční rozsah: 2,4 GHz
  • Vysílací výkon (EIRP): 100 mW
  • Vhodné pro použití v interiérech
  • Spotřeba energie: max. 1,5 W
  • Jmenovitý proud: 10 A / 250 V~
  • Jmenovitý výkon: 2500 W
  • Rozměry (DxŠxV): cca. 60 x 60 x 36 mm


Systémové požadavky

  • Brána WLAN


Obsah balení

  • WLAN switch napájecí zásuvky
  • Uživatelská příručka


Balení

  • Kartonová krabice

Technical characteristics
Frequency range
• 2.4 GHz band
Physical characteristics
Délka
• 60 mm
Width
• 60 mm
Height
• 36 mm
Barva
• bílá
What is the user name for the web interface if a password has been assigned? The default user name is "admin".
It is not possible to enter a WLAN password with an asterisk (*). The problem is solved with the current firmware version 6.5.0 since 22.10.19.
How to flash the device to the latest Tasmota version? For the socket switch we use a version of Tasmota, that we have adjusted and tested. Please understand that we can only support this Tasmota version.
What are the changes in firmware 6.7.1 since 6.3.20? • Fix WeMo emulation for 1G echo and 2G echo dot.
• Add command "time" to disable NTP and set UTC time
• Removed support for WPS.  
What are the changes in firmware 7.2? • Change default GUI to dark theme
• New Arduino Core version
• The LED is now controlled in the same way as Tasmota
• For the hardware configuration a user template is now used.
We recommend you save the device settings and do a "Reset 6" as console command. This will restore the default settings, but keep the WIFI SSID and Password.
Weaker Wi-Fi signal after firmware upgrade The Wi-Fi calibration needs to be deleted to force the device to re-calibrate Wi-Fi after it restarts.
1. Run "reset 3" in the Console (your existing settings will not be affected).
2. The device will restart
3. Cycle the power on the device (unplug and plug it).
Wi-Fi calibration will not be done unless the device performs a cold boot from power up.
 
Configuration options In case of problems, the following switches can help:
SetOption55 mDNS service 0 = disable 1 = enable
SetOption19 Set Home Assistant discovery protocol 0 = use Tasmota integration (default) 1 = use MQTT discovery
SetOption109 0 = (default) 1 = force gen1 Alexa mode, for Echo Dot 2nd gen devices only
The device does not connect to the Wi-Fi If your device does not connect to your Wi-Fi and you've made sure the Wi-Fi credentials are correct, it is caused by using special chars or white spaces in your SSID or Password of your Wi-Fi. Remove them and try again. Other reason can be using an SSID longer than the allowed 32 characters.
Všechny názvy a symboly zde uvedené jsou vlastnictvím výrobce.
Tiskové chyby, změny a chyby v datech vyhrazeny.